Yanmar ZT350 series Operation Manual Download Page 55

Page: 55 / 58

TROUBLESHOOTING

No.

Problem

Possible Cause

Action

Reference Page

Remote Control

Operates Hard, Binds,

Has Excessive Free

Play or Makes Unusu-

al Sounds

Insufficient lubrication

on the shift and throttle

(if applied) linkage

fasteners.

Lubricate.

Obstruction in the shift

or throttle (if applied)

linkages.

Remove the

obstruction.

Loose or missing shift

and throttle linkages.

Check all throttle link-

ages. If any are loose

or missing, see your

authorized Yanmar

Marine dealer or dis-

tributor immediately.

Shift or throttle (if

equipped) cable is

kinked.

Straighten the cable or

have your authorized

Yanmar Marine dealer

or distributor replace

the cable if damaged

beyond repair.

Steering Wheel Turns

Hard or Jerky

Low power steering

pump fluid level.

Check for leaks. Refill

the system with fluid.

—

Stern-drive belt is

loose or in poor

condition.

Replace and / or

adjust.

—

Insufficient lubrication

on the steering

components.

Lubricate.

Insufficient lubrication

on the transom gimbal

housing assembly and

swivel shaft.

Lubricate.

Loose or missing

steering fasteners or

parts.

Check all parts and

fasteners. If any are

loose or missing, see

your authorized Yan-

mar Marine dealer or

distributor

immediately.

Contaminated power

steering fluid.

See your authorized

Yanmar Marine dealer

or distributor.

—

ZT350 Operation Manual

Summary of Contents for ZT350 series



























































Search results

Summary of Contents for ZT350 series

Reviews:

Related manuals for ZT350 series

Brands by name

Popular brands

Yanmar ZT350 series, Operation Manual

Search results

Summary of Contents for ZT350 series

Reviews:

Related manuals for ZT350 series

Brands by name

Popular brands