Yamaha XP500 Service Manual Download

Page: 35 / 559

1 - 24

GEN

INFO

SPECIAL TOOLS

90890-03079

YM-34483

Thickness gauge

This tool is used to measure the valve
clearance.

Compression gauge

90890-03081

YU-33223

Extension

90890-04082

Compression gauge
Extension

These tools are used to measure engine
compression.

Vacuum gauge

90890-03094

YU-44456

Vacuum gauge

This gauge is used to synchronize the
throttle bodies.

90890-03112

YU-03112-C

Pocket tester

This tool is used to check the electrical
system.

90890-03141

YM-33277-B

Timing light

This tool is used to check the ignition tim-
ing.

90890-03149

Test coupler adaptor

This tool is used to check the ABS diag-
nosis.

Pressure gauge

90890-03153

Oil pressure adapter

90890-03124

Pressure gauge
Oil pressure adapter B

These tools are used to measure fuel
pressure and oil pressure.

90890-03158

Carburetor angle driver

This tool is used to turn the air screw
when syncronizing the throttle bodies.

Tool No.

Tool name/Function

Illustration

Summary of Contents for XP500
















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for XP500

Reviews:

Related manuals for XP500

Brands by name

Popular brands

Yamaha XP500, Service Manual

Search results

Summary of Contents for XP500

Reviews:

Related manuals for XP500

Brands by name

Popular brands