Yamaha PJP-MC24 Instruction Manual Download Page 83

Page: 83 / 92

Tro

les

oti

Other problems

Symptom



Cause



Solution

Cannot synchronize
the PJP-MC or PC
to an NTP server.
to the Web interface.

The NTP server IP address or
domain name is incorrect.

• Check to make sure that the settings

match the NTP server information.

•

Ping the NTP server to confirm that it is

functioning.

The route to the registered NTP

server has not been configured.

Check the provider and route settings.

An incorrect time
is displayed.

The time zone is not set
properly.

Set the time zone according to the
PJP-MC24 location.

Cannot log in on
CONSOLE Port

You are using a straight serial
cable.

Use a cross serial cable.

The serial port settings are
incorrect.

Set to 9600 bps, 8 bits, 1 stop bit, and no
parity (page 75).

Summary of Contents for PJP-MC24





























































































Search results

Summary of Contents for PJP-MC24

Reviews:

Related manuals for PJP-MC24

Brands by name

Popular brands

Yamaha PJP-MC24, Instruction Manual

Search results

Summary of Contents for PJP-MC24

Reviews:

Related manuals for PJP-MC24

Brands by name

Popular brands