Yamaha PJP-MC24 Instruction Manual Download Page 79

Page: 79 / 92

Tro

les

oti

Symptom



Cause



Solution

STATUS LED is
blinking.

The PJP-MC24 is
malfunctioning.

Initialize the PJP-MC24 (page 84), and

reconfigure its settings.

STATUS LED is
lighted.

There is a connection problem.

• Confirm that there is no connection

problem, and the IP Keepalive settings

are properly configured (page 29).

• The STATUS LED lights if the PJP-MC24

fails to connect to even one IP Keepalive
recipient address.

There is a connection
problem, but the
STATUS LED does
not light.

IP Keepalive has not been set.

Configure the IP Keepalive settings

(page 29).

The IP Keepalive function does
not detect a connection
problem.

Wait for a few minutes, and check the
STATUS LED again.

When LEDs are off or blinking

(continued)

Summary of Contents for PJP-MC24





























































































Search results

Summary of Contents for PJP-MC24

Reviews:

Related manuals for PJP-MC24

Brands by name

Popular brands

Yamaha PJP-MC24, Instruction Manual

Search results

Summary of Contents for PJP-MC24

Reviews:

Related manuals for PJP-MC24

Brands by name

Popular brands