Yamaha PJP-MC24 Instruction Manual Download Page 77

Page: 77 / 92

Tro

les

oti

Before Contacting Customer

Support

Before contacting customer support, please review
the information in this manual to see if you can use
it to solve your problem.

Confirm the following:

• Is the POWER LED on?

If not, refer to the next page.

• Is the LINK LED at the LAN port on?

If not, refer to the next page.

Check the STATUS LED

If it is on, there is a connection problem. See
page 79.

How to Fix Your Problem

Refer to the help chapter that matches the situation
most:

• Q1: When LEDs are off or blinking

(next page)

• Q: When the Web Interface is Not Working

(page 80)

• Q: When You Cannot Hold a Conference

(page 82)

• Q: Other Problems

(page 83)

If your problem was not solved

Contact YAMAHA customer support (page 86).

If you suspect a failure

Tro

les

oti

Summary of Contents for PJP-MC24





























































































Search results

Summary of Contents for PJP-MC24

Reviews:

Related manuals for PJP-MC24

Brands by name

Popular brands

Yamaha PJP-MC24, Instruction Manual

Search results

Summary of Contents for PJP-MC24

Reviews:

Related manuals for PJP-MC24

Brands by name

Popular brands