Yamaha PJP-MC24 Instruction Manual Download Page 57

Page: 57 / 92

Starting a Conference

You can start a conference after you have reserved it.

Starting a Conference According to Schedule

You can start a reserved conference at the scheduled time without operating the PJP-
MC24. The following explains the connection process for participants.

Prepare the ProjectPhone for the Conference.

• Turn on the ProjectPhone and connect its LAN cable, so that it will be able to connect to

the PJP-MC24.

• Disconnect the ProjectPhone from all other terminals.You can check the ProjectPhone

display to see whether or not the ProjectPhone is connected to other terminals and
whether or not it will be able to connect to the PJP-MC24.

Pre-conference

Conference Status

page display

The

Participants

list on the

Conference Status

(page 60) page displays

Will attend

in the status of scheduled conference participants.

Sta

rtin

g a

fer

ith

a R

erv

atio

Summary of Contents for PJP-MC24





























































































Search results

Summary of Contents for PJP-MC24

Reviews:

Related manuals for PJP-MC24

Brands by name

Popular brands

Yamaha PJP-MC24, Instruction Manual

Search results

Summary of Contents for PJP-MC24

Reviews:

Related manuals for PJP-MC24

Brands by name

Popular brands