Yamaha PJP-MC24 Instruction Manual Download Page 17

Page: 17 / 92

Step

Accessing the Web interface

Configure the PJP-MC24 by connecting it to a PC and

using a Web browser to access the

PJP-MC24 Web interface.
You can access the Web interface by following the steps outlined in this section.

Note

To access the Web interface, you need to use a Web browser equivalent to Windows Internet

Explorer 6.0 or later.

Confirm that the product is on.

Open a Web browser on the PC and click

Open

on the

File

menu.

Enter “http://192.168.100.101/” using single-byte alphanumerics,

and click

The Web interface’s user level main window opens.

If the Web interface’s user level main window does not open,

see “Q2: When the Web Interface is Not Working” (page 80).

Enter

Click

ett

g S

tar

ted

Summary of Contents for PJP-MC24





























































































Search results

Summary of Contents for PJP-MC24

Reviews:

Related manuals for PJP-MC24

Brands by name

Popular brands

Yamaha PJP-MC24, Instruction Manual

Search results

Summary of Contents for PJP-MC24

Reviews:

Related manuals for PJP-MC24

Brands by name

Popular brands