manualshive.com logo in svg

Yamaha GRIZZLY 350 YFM35GW, Owner'S Manual

The Yamaha GRIZZLY 350 YFM35GW is a powerful and reliable all-terrain vehicle designed to tackle any outdoor adventure. To ensure optimal performance and maintenance, it is essential to refer to the comprehensive Owner's Manual. Download your free copy of the manual from manualshive.com today and unlock the full potential of your GRIZZLY 350.

Share
Download
background image

5-1

5

EBU19200

PRE-OPERATION CHECKS

EBU19220

Pre-operation check list 

Before operating this ATV, be sure to check the items listed in the following table.

NOTE:

The maintenance of some items in the table has to be performed by a Yamaha dealer. Refer to the “Periodic
maintenance and lubrication chart” on page 8-3 to determine which service should be performed by a
Yamaha dealer.

ITEM

ROUTINE

PAGE

Fuel

• Check fuel level in fuel tank, and add recommended fuel if neces-

sary.

• Check fuel line for leakage. Correct if necessary.

4-9, 5-3

Engine oil

• Check oil level in engine, and add recommended oil to specified lev-

el if necessary.

• Check ATV for oil leakage. Correct if necessary.

5-3, 8-10

Final gear oil

• Check ATV for oil leakage. Correct if necessary.

5-3, 8-14

Front brake

• Check operation. If soft or spongy, have Yamaha dealer bleed hy-

draulic system.

• Check brake pads for wear, and replace if necessary.
• Check brake fluid level in reservoir, and add recommended brake 

fluid to specified level if necessary.

• Check hydraulic system for leakage. Correct if necessary.

5-3, 8-24, 8-25, 8-27

Rear brake

• Check operation, and correct if necessary.
• Lubricate cables if necessary.
• Check lever and pedal free play, and adjust if necessary.

5-3, 8-24, 8-27

U5WH63E0.book  Page 1  Monday, May 8, 2006  1:25 PM

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands

Load more brands