Yamaha GRIZZLY 350 YFM35GW Owner'S Manual Download | Manualshive

Page: 100 / 134

background image

8-23

8

crease the engine idling speed, turn the throt-
tle stop screw in direction (a), and to decrease
it, turn the screw in direction (b).

NOTE:

If the specified idling speed cannot be obtained as
described above, have a Yamaha dealer make the
adjustment.

EBU24043

Adjusting the throttle cable free play

The throttle cable free play should be checked
and, if necessary, adjusted at the intervals speci-
fied in the periodic maintenance and lubrication
chart.
The throttle cable free play should measure 3.0–
5.0 mm (0.12–0.20 in) at the throttle lever. Period-
ically check the throttle cable free play and, if nec-
essary, adjust it as follows.

NOTE:

The engine idling speed must be checked, and ad-
justed if necessary, before adjusting the throttle ca-
ble free play.

1. Loosen the locknut.
2. To increase the throttle cable free play, turn

the adjusting bolt in direction (a). To decrease
the throttle cable free play, turn the adjusting
bolt in direction (b).

1. Throttle stop screw

Engine idling speed:

1450–1550 r/min

U5WH63E0.book Page 23 Monday, May 8, 2006 1:25 PM

«
...
98
99
100
101
102
...
»

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands