background image

8-34

8

WARNING

EWB02160

Battery electrolyte is poisonous and danger-
ous, as it contains sulfuric acid, which can
cause severe burns. Avoid contact with skin,
eyes or clothing. Always shield your eyes
when working near batteries.
Antidote:
EXTERNAL: Flush with water.
INTERNAL: Drink large quantities of water or
milk. Follow with milk of magnesia, beaten egg
or vegetable oil. Call a physician immediately.
EYES: Flush with water for 15 minutes and get
prompt medical attention.
Batteries produce explosive gases. Keep
sparks, flame, cigarettes or other sources of ig-
nition away. Ventilate when charging or using
in an enclosed space.
KEEP OUT OF REACH OF CHILDREN.

To charge the battery

Have a Yamaha dealer charge the battery as soon
as possible if it seems to have discharged. Keep in
mind that the battery tends to discharge more
quickly if the ATV is equipped with optional electri-
cal accessories.

To store the battery

1. If the ATV will not be used for more than one

month, remove the battery, fully charge it, and
then place it in a cool, dry place.

2. If the battery will be stored for more than two

months, check it at least once a month and ful-
ly charge it if necessary.

To install the battery

NOTE:

Be sure the battery is fully charged.

1. Place the battery in its compartment.
2. Make sure to properly connect the battery

leads to the battery terminals.

U5WH63E0.book  Page 34  Monday, May 8, 2006  1:25 PM

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Reviews:

Related manuals for GRIZZLY 350 YFM35GW