manualshive.com logo in svg

Yamaha GRIZZLY 350 YFM35GW, Owner'S Manual

The Yamaha GRIZZLY 350 YFM35GW is a powerful and reliable all-terrain vehicle designed to tackle any outdoor adventure. To ensure optimal performance and maintenance, it is essential to refer to the comprehensive Owner's Manual. Download your free copy of the manual from manualshive.com today and unlock the full potential of your GRIZZLY 350.

Share
Download
background image

4-8

4

EBU18670

Recoil starter 

Firmly grasp the handle and pull slightly until en-
gagement can be felt. Then pull forcefully, being
careful not to pull the rope all the way out.

WARNING

EWB00340

Shift the drive select lever into the neutral po-
sition and apply the parking brake before start-
ing the engine, otherwise the ATV could start
to move unexpectedly, which could cause an
accident.

EBU18720

Fuel tank cap 

Remove the fuel tank cap by turning it counter-
clockwise.

1. Drive select lever

1. Recoil starter

U5WH63E0.book  Page 8  Monday, May 8, 2006  1:25 PM

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands

Load more brands