Yamaha GRIZZLY 350 YFM35GW Owner'S Manual Download

Page: 113 / 134

8-36

The main fuse and the fuse box are located under
the seat. (See page 4-12.)
If a fuse is blown, replace it as follows.

1. Turn the key to “OFF” and turn off all electrical

circuits.

CAUTION:

ECB00640

To prevent accidental short-circuiting, turn off
the main switch when checking or replacing a
fuse.

2. Remove the blown fuse, and then install a

new fuse of the specified amperage.

WARNING

EWB02171

Always use a fuse of the specified rating, and
never use a substitute object in place of the
proper fuse. An improper fuse or a substitute
object can cause damage to the electrical sys-
tem, which could lead to a fire.

3. Turn the key to “ON” and turn on the electrical

circuits to check if the devices operate.

4. If the fuse immediately blows again, have a

Yamaha dealer check the electrical system.

1. Headlight fuse
2. Ignition fuse

3. Auxiliary DC jack fuse (for optional auxiliary DC jack)

4. Signaling system fuse
5. Spare fuse

Specified fuses:

Main fuse:

30.0 A

Headlight fuse:

15.0 A

Ignition fuse:

15.0 A

Signaling system fuse:

10.0 A

Auxiliary DC jack fuse:

10.0 A

U5WH63E0.book Page 36 Monday, May 8, 2006 1:25 PM

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Search results

Summary of Contents for GRIZZLY 350 YFM35GW

Reviews:

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands

Yamaha GRIZZLY 350 YFM35GW, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 350 YFM35GW

Reviews:

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands