Yamaha GRIZZLY 350 YFM35GW Page 125 Owner'S Manual Download

Page: 125 / 134

10-3

Transmission type:

V-belt automatic

Operation:

Left hand operation

Forward gear:

35/20 (1.750)

Reverse gear:

26/15 (1.733)

Chassis:

Frame type:

Steel tube frame

Caster angle:

4.0 °

Trail:

21.0 mm (0.83 in)

Front tire:

Type:

Tubeless

Size:

AT25 x 8-12

Manufacturer/model:

CHENG SHIN/C-828 (AUS)(NZL)
MAXXIS/M979 (EUR)(GBR)

Rear tire:

Type:

Tubeless

Size:

AT25 x 10-12

Manufacturer/model:

CHENG SHIN/C-828 (AUS)(NZL)
MAXXIS/M980 (EUR)(GBR)

Loading:

Maximum loading limit:

210.0 kg (463 lb)
(Total weight of rider, cargo, accessories, and tongue)

Tire air pressure (measured on cold tires):

Recommended:

Front:

25.0 kPa (3.6 psi) (0.250 kgf/cm²)

Rear:

25.0 kPa (3.6 psi) (0.250 kgf/cm²)

Minimum:

Front:

22.0 kPa (3.2 psi) (0.220 kgf/cm²)

Rear:

22.0 kPa (3.2 psi) (0.220 kgf/cm²)

Maximum:

Front:

28.0 kPa (4.1 psi) (0.280 kgf/cm²)

Rear:

28.0 kPa (4.1 psi) (0.280 kgf/cm²)

Front wheel:

Wheel type:

Panel wheel

Rim size:

12 x 6.0AT

Rear wheel:

Wheel type:

Panel wheel

Rim size:

12 x 7.5AT

U5WH63E0.book Page 3 Monday, May 8, 2006 1:25 PM

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Search results

Summary of Contents for GRIZZLY 350 YFM35GW

Reviews:

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands

Yamaha GRIZZLY 350 YFM35GW, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 350 YFM35GW

Reviews:

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands