Yamaha GRIZZLY 350 YFM35GW Owner'S Manual Download

Page: 105 / 134

8-28

Adjusting the brake pedal free play

The brake pedal free play should measure 20.0–
30.0 mm (0.79–1.18 in) as shown. If the free play
is incorrect, adjust it as follows.

1. Fully loosen the brake lever free play adjust-

ing nut on the brake cable at the rear wheel
hub.

2. Turn the brake pedal free play adjusting nut

on the brake cable at the rear wheel hub in di-
rection (a) to increase the free play, and in di-
rection (b) to decrease it.

Adjusting the brake lever free play

The brake lever free play should measure 3.0–5.0
mm (0.12–0.20 in) as shown. If the free play is in-
correct, adjust it as follows.

1. Brake pedal free play

1. Brake pedal free play adjusting nut
2. Brake lever free play adjusting nut

U5WH63E0.book Page 28 Monday, May 8, 2006 1:25 PM

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Search results

Summary of Contents for GRIZZLY 350 YFM35GW

Reviews:

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands

Yamaha GRIZZLY 350 YFM35GW, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 350 YFM35GW

Reviews:

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands