manualshive.com logo in svg

Yamaha GRIZZLY 350 YFM35GW, Owner'S Manual

The Yamaha GRIZZLY 350 YFM35GW is a powerful and reliable all-terrain vehicle designed to tackle any outdoor adventure. To ensure optimal performance and maintenance, it is essential to refer to the comprehensive Owner's Manual. Download your free copy of the manual from manualshive.com today and unlock the full potential of your GRIZZLY 350.

Share
Download
background image

8-30

8

4. Tighten the locknut at the brake lever.

NOTE:

When adjusting the rear brake lever free play:

●

Be sure not to step on the brake pedal.

●

Make sure the brake pedal does not move.

WARNING

EWB02080

Operating with improperly serviced or adjust-
ed brakes could cause loss of braking ability,
which could lead to an accident.
After servicing:

●

Make sure the brakes operate smoothly and
that the free play is correct.

●

Make sure the brakes do not drag.

Replacement of brake components requires
professional knowledge. These procedures
should be performed by a Yamaha dealer.

EBU24751

Brake light switches 

The operation of the brake light switches must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.
The brake light switch for the brake pedal can be
adjusted as follows, but the other brake light
switches should be adjusted by a Yamaha dealer.

1. Remove panel A. (See page 8-8.)

NOTE:

The brake light switch is properly adjusted when
the brake light comes on just before braking takes
effect.

2. Turn the adjusting nut while holding the brake

light switch in place. To make the brake light
come on earlier, turn the adjusting nut in direc-
tion (a). To make the brake light come on lat-
er, turn the adjusting nut in direction (b).

1. Locknut
2. Brake lever free play adjusting bolt

U5WH63E0.book  Page 30  Monday, May 8, 2006  1:25 PM

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands

Load more brands