manualshive.com logo in svg

Yamaha GRIZZLY 350 YFM35GW, Owner'S Manual

The Yamaha GRIZZLY 350 YFM35GW is a powerful and reliable all-terrain vehicle designed to tackle any outdoor adventure. To ensure optimal performance and maintenance, it is essential to refer to the comprehensive Owner's Manual. Download your free copy of the manual from manualshive.com today and unlock the full potential of your GRIZZLY 350.

Share
Download
background image

8-8

8

EBU23080

Removing and installing the panel 

The panel shown needs to be removed to perform
some of the maintenance jobs described in this
chapter. Refer to this section each time the panel
needs to be removed and installed.

EBU23111

Panel A

To remove the panel
Remove the bolt, and then take the panel off.

To install the panel
Place the panel in the original position and install
the bolt.

CAUTION:

ECB00380

When installing the panel, be sure not to pinch
the cables or wires.

EBU23211

Checking the spark plug 

The spark plug is an important engine component,
which is easy to check. Since heat and deposits
will cause any spark plug to slowly erode, the spark

1. Panel A

1. Panel A
2. Bolt

U5WH63E0.book  Page 8  Monday, May 8, 2006  1:25 PM

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands

Load more brands