Yamaha GRIZZLY 350 YFM35GW Page 58 Owner'S Manual Download | Manualshive

Page: 58 / 134

background image

7-5

7

WARNING

EWB01410

Never operate this ATV without wearing an ap-
proved motorcycle helmet, eye protection and
protective clothing. Operating without an ap-
proved motorcycle helmet increases your
chances of a severe head injury or death in the
event of an accident. Operating without eye
protection can result in an accident and in-
creases your chances of a severe injury in the
event of an accident. Operating without protec-
tive clothing increases your chances of severe
injury in the event of an accident.

Do not operate after consuming alcohol or
drugs.

The operator’s performance capability is reduced
by the influence of alcohol or drugs.

WARNING

EWB01420

Never consume alcohol or drugs before or
while driving this ATV.

Pre-operation checks

Always perform the pre-operation checks listed on
page 5-1 before riding for proper care of the ATV
and to ensure safety.

WARNING

EWB01430

Always inspect your ATV each time you use it
to make sure the ATV is in safe operating con-
dition. Always follow the inspection and main-
tenance procedures and schedules described

U5WH63E0.book Page 5 Monday, May 8, 2006 1:25 PM

«
...
56
57
58
59
60
...
»

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35GW

GRIZZLY 550 FI YFM5FGY

Brand: Yamaha Pages: 168

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands