Yamaha GRIZZLY 350 YFM35GW Owner'S Manual Download | Manualshive

Page: 56 / 134

background image

7-3

7

Not recommended for children under 16 years
of age.

WARNING

EWB01390

A child under 16 should never operate an ATV
with engine size greater than 90 cc. Use by chil-
dren of ATVs that are not recommended for
their age can lead to severe injury or death of
the child.

This ATV is designed to carry operator and car-
go only – passengers prohibited.

WARNING

EWB01400

Never carry a passenger. The long seat is to al-
low the operator to shift position as needed
during operation. It is not for carrying passen-
gers. Carrying a passenger on this ATV greatly
reduces your ability to balance and control this
ATV. It could cause an accident, resulting in
harm to you and/or your passenger.

U5WH63E0.book Page 3 Monday, May 8, 2006 1:25 PM

«
...
54
55
56
57
58
...
»

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands