Yamaha GRIZZLY 350 YFM35GW Page 37 Owner'S Manual Download | Manualshive

Page: 37 / 134

background image

4-15

4

NOTE:

A special wrench can be obtained at a Yamaha
dealer to make this adjustment.

WARNING

EWB00400

Always adjust the shock absorber assemblies
on the left and right side to the same setting.
Uneven adjustment can cause poor handling
and loss of stability, which could lead to an ac-
cident.

EBU19020

Adjusting the rear shock absorber as-
sembly

The spring preload can be adjusted to suit the rid-
er’s weight and the riding conditions.
Adjust the spring preload as follows.
Turn the adjusting ring in direction (a) to increase
the spring preload and thereby harden the suspen-
sion, and in direction (b) to decrease the spring
preload and thereby soften the suspension.

1. Special wrench

Spring preload setting:

Minimum (soft):

1

Standard:

2

Maximum (hard):

5

U5WH63E0.book Page 15 Monday, May 8, 2006 1:25 PM

«
...
35
36
37
38
39
...
»

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35GW

GRIZZLY 350 YFM35GX

Brand: Yamaha Pages: 134

GRIZZLY 350 YFM350TF

Brand: Yamaha Pages: 140

GRIZZLY 350 YFM35GDXG

Brand: Yamaha Pages: 146

GRIZZLY 350 YFM350TE

Brand: Yamaha Pages: 140

GRIZZLY 350 YFM35FGDY

Brand: Yamaha Pages: 144

GRIZZLY 350 YFM350FAZ

Brand: Yamaha Pages: 142

GRIZZLY 350 YFM350FAB

Brand: Yamaha Pages: 142

GRIZZLY 125 YFM125GB

Brand: Yamaha Pages: 132

GRIZZLY 350 YFM350DF

Brand: Yamaha Pages: 146

GRIZZLY 350 YFM350DE

Brand: Yamaha Pages: 144

Brand: Yamaha Pages: 154

Brand: Yamaha Pages: 350

GRIZZLY 125 YFM125GT

Brand: Yamaha Pages: 362

BRUIN 350 YFM350AS

Brand: Yamaha Pages: 384

Brand: Yamaha Pages: 396

BRUIN 350 YFM350FAT

Brand: Yamaha Pages: 400

Brand: Yamaha Pages: 402

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands