Yamaha GRIZZLY 350 YFM35GW Owner'S Manual Download | Manualshive

Page: 36 / 134

background image

4-14

4

EBU18960

Front carrier

●

Do not exceed the load limit of 40.0 kg (88 lb) for
the front carrier.

●

Do not exceed the maximum load of 210.0 kg
(463 lb) for the ATV.

EBU18970

Rear carrier

●

Do not exceed the load limit of 80.0 kg (176 lb)
for the rear carrier.

●

Do not exceed the maximum load of 210.0 kg
(463 lb) for the ATV.

EBU18990

Adjusting the front shock absorber as-
semblies

The spring preload can be adjusted to suit the rid-
er’s weight and the riding conditions.
Adjust the spring preload as follows.
Turn the adjusting ring in direction (a) to increase
the spring preload and thereby harden the suspen-
sion, and in direction (b) to decrease the spring
preload and thereby soften the suspension.

1. Storage compartment check hose

1. Spring preload adjusting ring

2. Position indicator

U5WH63E0.book Page 14 Monday, May 8, 2006 1:25 PM

«
...
34
35
36
37
38
...
»

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands