Yamaha GRIZZLY 350 YFM35GW Owner'S Manual Download | Manualshive

Page: 104 / 134

background image

8-27

8

EBU24390

Checking the front brake lever free play

The brake lever free play must be checked at the
intervals specified in the periodic maintenance and
lubrication chart. The brake lever should have a
free play of zero mm (zero in) as shown. If the free
play is incorrect, have a Yamaha dealer check the
brake system.

WARNING

EWB02070

Operating with improperly serviced or adjust-
ed brakes could cause loss of braking ability,
which could lead to an accident.
After servicing:

●

Make sure the brakes operate smoothly and
that the free play is correct.

●

Make sure the brakes do not drag.

●

Make sure the brakes are not spongy. All air
must be bled from the brake system.

Replacement of brake components requires
professional knowledge. These procedures
should be performed by a Yamaha dealer.

EBU24511

Adjusting the brake pedal and rear
brake lever free play

The brake pedal and brake lever free play must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

NOTE:

●

Always perform this maintenance completely in
the following order whenever adjusting the rear
brake.

●

Before adjusting the brake lever and brake pedal
free play, check the rear brake shoes for wear.

1. Brake lever free play

U5WH63E0.book Page 27 Monday, May 8, 2006 1:25 PM

«
...
102
103
104
105
106
...
»

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands