Xerox WorkCentre Pro 423, Service Manual

Page: 241 / 619

03/02 How to use the Diagnostic C/E Mode
WorkCentre Pro 423/428 2-209 CHAPTER 2 TROUBLESHOOTING
Communication Parameters of Individual Settings to Speed Dial Numbers in CE
If Speed (abbreviated) dial numbers are set in CE mode, the communication parameters listed in the table below can be individually to the numbers, irrespective of the Ch-Func set values.
If "Auto" is set, the Ch-Func set values are selected. The default is "Auto" for all the items below.
Depending on the item, the setting contents differ from those of Ch-Func. Set the parameters to each abbreviated dial number by referencing the table below and system data.
Panel
display No. Panel display
item name Contents Abbreviated dial settings and notes Corresponding Ch-Func settings (Underline: default)
19 Send ATT
level Tone (image
signal) send level 0 to 15, auto
•
The values from 0 to 15 are the same as those in the Ch-Func setting range.
57-550
Setting range 0 to 20(0=-10dBm,
1 step=-1dBm)
20 DIS pass
count Number of ignoring
DIS from remote
terminal 0 to 14, auto
•
The values from 0 to 14 are the same as those in the Ch-Func setting range.
57-576
Setting range 0 to 255(1 step=once)
21 Modem
speed Maximum modem
speed at
transmission and
polling 0 to 14, auto
•
The values from 1 to 14 are the same as those in the Ch-Func setting range.
•
Do not use 0 reserved for future use.
57-601
Setting range 1 to 14
1=2400bps to 14=336000 bps
22 Transmission
equalizer
value Value of the
transmission cable
equalizer 0 to 14, auto
•
The values from 0 to 3 are the same as those in the Ch-Func setting range.
•
Do not use 4 to 14 reserved for future use.
57-554
Setting range 0, 1, 2, 3
0=0dB, 1=4dB, 2=8dB, 3=12dB
23 Reception
equalizer
value Value of the
reception equalizer 0 to 14, auto
•
The values from 0 to 3 are the same as those in the Ch-Func setting range.
•
Do not use 4 to 14 reserved for future use.
57-555
Setting range 0, 1, 2, 3
0=0dB, 1=4dB, 2=8dB, 3=12dB
24 ECM ECM mode at
transmission and
polling OFF, ON, auto
•
ECM communication with each destination can be turned OFF and ON, irrespective
of the Ch-Func settings.
57-690
0=OFF, 1=ON
25 SG3(V.34) SuperG3 mode at
transmission and
polling OFF, ON, auto
•
SG3 communication with each destination can be turned OFF and ON, irrespective
of the Ch-Func settings.
57-520
0=OFF, 1=ON
26 JBIG JBIG-BASIC
communication at
transmission and
polling Disable(JBIG comm. OFF), Enable(ON), auto
•
Even when the Ch-Func setting is ON, JBIG-BASIC comm. with each destination
can be turned OFF by setting "Disable" here. (However, JBIG does document read.)
-- "58-051" sets the document read mode.
57-051
Setting range 1, 2, 3, 5, 6
1=MH, 2=MR, 3=MMR, 5=JBIG-BASIC, 6=JBIG-OPTION
(Do not use 6 reserved for future use.)