Xerox M20I - WorkCentre B/W Laser System Administration Manual Download Page 28

Page: 28 / 218

Page 2-2

Xerox WorkCentre M20i System Administration Guide

Basic N

ork

Installat

ion

Information Checklist

Before starting the basic network installation procedures, please ensure the following items
are available or have been performed:

If problems are encountered during the WorkCentre M20i installation, refer to the Problem
Solving chapter for assistance.

CAUTION: Do not connect the network cable to the

WorkCentre M20i

until instructed

to do so.

Item

An existing operational network utilizing TCP/IP is required, these
procedures are not designed to install a network.

Customer

A suitable network cable.

Customer

If you are going to configure TCP/IP manually, you need to obtain and
record the following information:

• TCP/IP Address:

• Gateway Address:

• Subnet Mask Address:

• Primary DNS Server Address:

Refer to the Glossary for additional information on the Gateway
Address, Subnet Mask Address and Primary DNS, if needed.

Customer

Test the

WorkCentre M20i

to ensure it is installed fully and functioning

correctly.

Customer

WorkCentre M20i

print and fax drivers.

Xerox

Summary of Contents for M20I - WorkCentre B/W Laser



























































































































































































































Search results

Summary of Contents for M20I - WorkCentre B/W Laser

Reviews:

Related manuals for M20I - WorkCentre B/W Laser

Brands by name

Popular brands

Xerox M20I - WorkCentre B/W Laser, System Administration Manual

Search results

Summary of Contents for M20I - WorkCentre B/W Laser

Reviews:

Related manuals for M20I - WorkCentre B/W Laser

Brands by name

Popular brands