Xerox DocuPrint C2255 Quick Referenc Manual Download Page 92

Page: 92 / 106

A Appendix

Tighten the two screws to secure the control
board in place.

10. Connect the connector conversion cable to

the Parallel Port connector.

Note

• Connect the parallel cable to the connector on other end

of the connector conversion cable. For more
information, refer to “Connecting a cable” (P. 22).

11. Connect the power cord to the printer.

Press the <|> side of the printer's power
switch to turn on the power.

12. Print the [Configuration Report] and confirm

that [Parallel] is included in the
[Communication Settings] section.

Refer to

• List printing procedure: “Printing a Report/List” (P. 36)

Parallel Port installation is now complete.

Installing the TC/SC Font
ROM

This section describes how to install the TC/SC
Font ROM on the printer.

Switch the power off by pressing the < >
side of the power switch.

Unplug the power cord from the power outlet
and the printer.

Loosen the two screws on the back right side
of the printer.

TC/SC Font ROM

Summary of Contents for DocuPrint C2255











































































































Search results

Summary of Contents for DocuPrint C2255

Reviews:

Related manuals for DocuPrint C2255

Brands by name

Popular brands

Xerox DocuPrint C2255, Quick Referenc Manual

Search results

Summary of Contents for DocuPrint C2255

Reviews:

Related manuals for DocuPrint C2255

Brands by name

Popular brands