Xerox DocuPrint C2255 Quick Referenc Manual Download Page 89

Page: 89 / 106

Installing the Feature Enhance Kit

Aligning the notch in the ROM card with the
tab in the R2 slot, insert the card straight into
the slot. Next, press the ROM card down
firmly into the slot.

Note

• Make sure the ROM card is inserted securely as far as it

can go.

• When the ROM card is installed correctly, the retaining

clips on both ends stand up.

Reinsert the control board back into the
printer. Holding its handle, slide the control
board back into the printer.

Press the control board in as far as it will go.

Tighten the two screws to secure the control
board in place.

Connect the power cord to the printer.
Press the <|> side of the printer's power
switch to turn on the power.

The installation is now complete.
Next, continue from step 9 enable the Feature
Enhance Kit feature from the control panel.

Important

• Once you install the Feature Enhance Kit and enable it

with the control panel, that Feature Enhance Kit is not
usable on any other printer.

Press the <Menu> button on the control
panel to display the menu screen.

10. Press the < > button until [Admin Menu] is

displayed.

11. Press the < > or <OK> button to select.

[Network/Port] is displayed.

12. Press the < > button until [System Settings]

is displayed.

13. Press the < > or <OK> button to select.

[Alert Tone] is displayed.

Insert securely as

far as it can go.

LanguageEmulation

Admin Menu

Network/Port

Admin Menu

System Settings

Alert Tone

Summary of Contents for DocuPrint C2255











































































































Search results

Summary of Contents for DocuPrint C2255

Reviews:

Related manuals for DocuPrint C2255

Brands by name

Popular brands

Xerox DocuPrint C2255, Quick Referenc Manual

Search results

Summary of Contents for DocuPrint C2255

Reviews:

Related manuals for DocuPrint C2255

Brands by name

Popular brands