Wurlitzer International L Page 82 Operating Instructions Manual Download | Manualshive

Page: 82 / 88

background image

Error messages

International L – edition: 17.02.2006

82

Error no.

Error

Possible reason and remedy

71

Hex number in price memory (RAM).

Check all the prices and make any neces-
sary correction. In case of the error code
appearing frequently replace the IVC con-
trol unit.

72

Credit has turned negative.

Fault in credit calculation. Change IVC.

73

A basic price of 0 is transmitted to the
control system from an external coin sys-
tem (Executive or similar) MDB: coin se-
paration fault.

Coin unit faulty - change.

74

Selection price in connection with Execu-
tive is higher than 250 times basic price
or not entered in basic price units.

MDB: sensor is faulty.

Check prices and correct if 250 times hig-
her than basic price.

75

Fault in selection/column allocation.
MDB: coin acceptor gives no response.

76

Data in coin validator Simplex 0 not corre-
sponding to programmed data in IVC.

MDB: coin jammed

This error code may appear after you
have either replaced a coin validator or a
complete coin mechanism. To rectify, call
up service program 11, button 1 to re-pro-
gramme. Carry out transfer of a data
block (digits 9999)

see chapt. 9.9 on page

77

Interruption in data transmission between
coin validator and IVC.

Valid for all coin systems.

There is a break in communication bet-
ween the control unit and the coin system
(or coin validator). This break is most li-
kely due to a defective communication
cable between the coin validator/coin sys-
tem and the IVC control unit, or a re-pro-
gramming has to be carried out.

78

MDB checksum fault.

«
...
80
81
82
83
84
...
»

Summary of Contents for International L

























































































Reviews:

No comments

Related manuals for International L

APW-895N/IP-420

Brand: SanDisk Pages: 125

Brand: Panasonic Pages: 88

Brand: Duerkopp Adler Pages: 35

Brand: Sagem Pages: 67

Brand: Radio Shack Pages: 28

Brand: JUKI Pages: 12

Brand: Baby Lock Pages: 40

Brand: Canon Pages: 116

Brand: Canon Pages: 7

Brand: Canon Pages: 13

Brand: Canon Pages: 139

Brand: Canon Pages: 140

Brand: Canon Pages: 187

Brand: Canon Pages: 119

Brand: Canon Pages: 141

Brand: Canon Pages: 96

Brand: Canon Pages: 212

B45 - Faxphone B45 Bubble Jet Fax Machine

Brand: Canon Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands