Wurlitzer International L Page 34 Operating Instructions Manual Download | Manualshive

Page: 34 / 88

background image

Operation with MDB

International L – edition: 17.02.2006

34

9.9

"Data block" transfer - service program 11, button 1

A certain data block has to be transfered from the MDB to the memory of the IVC control unit (com-
pressed data over coin denominations, coin options and basic coins). Whenever necessary, for ex-
ample after alterations or changes in the coin system, carry out the following programming steps or
control that the data stored is correct and valid:

ATTENTION! For MDB systems the data block transfer should be carried out 30 seconds after ma-
chine has been taken into operation. In case you don't keep this limit faulty functions in communica-
tion between the IVC control unit and the MDB system may arise.

Press key P - hold it - and press key S seven times, display
shows

Press button 1, display shows the value of the lowest coin:
0.05 EURO

Press key P - hold it - display is

Enter the digits 9999, then display shows
Release key P.

Finally leave the service program (

9.10

Programming of the bill input - service programs 11, 12, 14

You can connect a bill acceptor, which sends serial impluses according to accepted bill values, to P8
of the IVC control unit.

NOTE: For bill validators accepting different bills, you have to programme the value of the lowest bill
(i.e. 5.00 EURO). Bills of higher values will be simulated through a certain number of impulses, i.e. 4
impulses of value 5.00 EURO for a 20.00 EURO-bill. In case this 20.00 EURO bill should be ac-
cepted, you have to programme the number of bills to be accepted to 4.

You should carry out following programming in succession:

9.10.1

Programming of the bill value - service program 11, button 9

Press button P - hold it - and press button S 7 times, display
shows:

Press button 9, display shows i.e.
indicating that the current programmed value of the bill is
10.00 EURO.

Alteration:

Press button P - hold it - display shows

Enter the new basic value in 4 digits, i.e. 0500 for 5.00 EURO,
display shows

Release button P.

11 COIN CHANNEL
SETTINGS

SELECTION:
01 =0005

SELECTION:
01 =

SELECTION:
=0010

11 COIN CHANNEL
SETTINGS

SELECTION:
09 =1000

SELECTION:
09 =

SELECTION:
=2000

«
...
32
33
34
35
36
...
»

Summary of Contents for International L

























































































Reviews:

No comments

Related manuals for International L

Brand: Necchi Pages: 64

Brand: GBC Pages: 120

Brand: Elba Pages: 17

Brand: White Pages: 44

Brand: MD SPORTS Pages: 26

Brand: Toyota Pages: 48

Brand: Lumina Pages: 40

Brand: Sagem Pages: 2

Brand: Olivetti Pages: 64

Brand: Horizon Fitness Pages: 70

Progression Els

Brand: Gamma Pages: 20

GARUDAN GPS/G-4032

Brand: Anita Pages: 101

Nevada Gold Classic

Brand: Arrow International Pages: 2

Brand: Janome Pages: 34

Brand: Lafferty Pages: 16

Brand: Muratec Pages: 138

Brand: Canon Pages: 2

Brand: JUKI Pages: 136

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands