Wolf Garten Lycos 40 M Series, Original Operating Instructions

Page: 23 / 179

Servicing
23
EN
Mains socket connection (230 V, 50 Hz)
WARNING!
Risk of injuries or material damage.
¾
Observe the mains voltage.
¾ The power source voltage must
match the information on the device
LGHQWL¿FDWLRQSODWH
¾ Only connect to a socket, that is
SURWHFWHGE\D$VORZEORZIXVH
(or an MCB).
Note
7KHSURWHFWLYHGHYLFHVSURWHFW\RXDJDLQVW
VHYHUHLQMXU\LQWKHHYHQWRI\RXUFRPLQJ
into contact with damaged/bare wires, if an
LQVXODWLRQGHIHFWH[LVWVDQGXQGHUFHUWDLQ
FLUFXPVWDQFHVLIGDPDJHWROLYHZLUHV
occurs.
• We recommend that you only connect the
device to power outlets that are protected by
a residual current device (RCD) with a tripping
FXUUHQWRIQRPRUHWKDQP$
• For older wiring installations, upgrade kits are
DYDLODEOH&RQVXOWDTXDOL¿HGHOHFWULFLDQ
Switching the device on/off
5
WARNING!
Risk of injuries due to the rotating line.
 Tool continues running!
¾ Always wait until the cutting tool comes
to a standstill.
¾ Hold the trimmer parallel to the lawn
before switching on.
Switching the device on
Î
Press the lock-on switch on the handle
$
.
Î
6LPXOWDQHRXVO\SUHVVWKHRQRႇVZLWFKRQWKH
handle
%
.
Î
Release the lock-on switch again.
3
The device operates.
6ZLWFKLQJWKHGHYLFHRႇ
Î
5HOHDVHWKHRQRႇVZLWFKWRVZLWFKWKHGHYLFH
Rႇ
'
.
3
7KHGHYLFHLVVZLWFKHGRႇ
Note
The cutting tool continues to run for a brief
SHULRGDIWHUEHLQJVZLWFKHGR௺
Adjusting the line
Typ 1
2
Î
3UHVVWKHUXQQLQJGHYLFHEULHÀ\RQWR¿UPJURXQG
e.g. a paving stone using the press knob (pressing
down force about 3 kg). About 1.5 cm of cutting
line is automatically fed out.
Typ 2
:LWKHDFKVZLWFKLQJRႇDQGRQWKHOLQHLVDGMXVWHG
automatically out of the line box.
Note
)UHTXHQWO\VZLWFKLQJRQDQGR௺ZLWKRXWUHD -
son results in increased line wear.
Note
If the cutting line becomes too short during
RSHUDWLRQGXHWRZHDUVZLWFKWKHGHYLFHR௺
DQGWKHQEDFNRQDJDLQWRH[WHQGWKHZRU -
NLQJOHQJWKRIWKHFXWWLQJOLQHDXWRPDWLFDOO\
Servicing
WARNING!
Risk of injuries or material damage.
¾ Only clean or service the device if the
motor is stationary and also the cutting
tool.
¾ Pull out the mains plug before any work
on the device!
¾
Repair and service work as well as the
replacement of safety elements must
EHSHUIRUPHGE\DTXDOL¿HGH[SHUWRU
workshop.
Cleaning the trimmer
Î
6ZLWFKWKHWULPPHURႇDQGZDLWXQWLOWKHFXWWLQJ
tool comes to a standstill.
Î
Clean the device with a hand brush after every
use.
Î
Clean the ventilation slots and underside of the
device at regular intervals to remove grass resi-
dues.
Attention!
Do not clean the device with water.