Winterthur Gas & Diesel Ltd. X52 Operation Manual Download Page 255

Page: 255 / 519

Tab 6-17

SYSTEM STATUS

Item

Function

Effect

001

START AST button

Starts the engine in astern direction (for reversible engine)

002

STOP button

Stops the engine

003

START AHD button

Starts the engine in ahead direction

004

CTRL. TR. button

Sends a signal for a control transfer to this LDU-20

005

INDEX button

Opens the INDEX page

006

Refresh button

Updates the module status list

007

Status indications for each module Shows either:

•

Initialization:

Hardware module has been reset and

bootloader has started the application

•

Bootloader, staying in bootloader:

Different version of

application/configuration/DSP is found, SW download is
necessary to synchronize the module with the rest of the
system

•

Pre-operational, synchronization:

Module is booting up

and waits for synchronization

•

Pre-operational, ready:

Module is booting up, every-

thing set-up successfully and is ready to enter Opera-
tional state

•

Operational:

Module operates correctly, System soft-

ware and application initialized successfully

•

None:

Module is set to OFF or disconnected from the

CAN bus

•

Stopped:

Module is not configured correctly, system ini-

tialization has failed, state is transitioned from pre-oper-
ational state

The usual working cycle is as follows:

•

Reset

•

Initialization

•

Pre-operational --> Stopped --> Reset

•

Operational --> Stopped --> Reset

008

Download button

Does a software download on the selected modules

X52

AA00-9606-34AAA-043B-A

Operation Manual

LDU-20 page - SYSTEM STATUS

Winterthur Gas & Diesel Ltd.

- 255 -

Issue 002 2018-11

Summary of Contents for X52








































































































































































































































































































































































































































































































































Search results

Summary of Contents for X52

Reviews:

Related manuals for X52

Brands by name

Popular brands

Winterthur Gas & Diesel Ltd. X52, Operation Manual

Search results

Summary of Contents for X52

Reviews:

Related manuals for X52

Brands by name

Popular brands