Winterthur Gas & Diesel Ltd. X52 Operation Manual Download Page 125

Page: 125 / 519

Fig 5-7

Cylinder - cooling water outlet (generic)

Legend

001

Exhaust valve cage

003

Cooling water outlet

002

Cylinder cover

Cooling water flows from the bottom water guide jacket to the top water guide jacket. Then the
cooling water flows into the cylinder cover (002,

Figure 5-7

) and the exhaust valve cage (001).

The cooling water flows back through the cooling water outlet (003) to the cooling water system
of the plant.

To prevent unwanted tension in the top part of the cylinder liner (004,

Figure 5-6

), the temperature

of the cooling water must stay in the permitted range:

•

±2°C at constant load

•

±4°C during load changes.

X52

AA00-2124-00AAA-043A-A

Operation Manual

Cylinder liner

Winterthur Gas & Diesel Ltd.

- 125 -

Issue 002 2018-11

Summary of Contents for X52








































































































































































































































































































































































































































































































































Search results

Summary of Contents for X52

Reviews:

Related manuals for X52

Brands by name

Popular brands

Winterthur Gas & Diesel Ltd. X52, Operation Manual

Search results

Summary of Contents for X52

Reviews:

Related manuals for X52

Brands by name

Popular brands