Winterthur Gas & Diesel Ltd. X52 Operation Manual Download Page 178 | Manualshive

Page: 178 / 519

background image

5.6.2

Turbocharger

The compressor (001,

) of the turbocharger compresses the air to the applicable

pressure. The compressor is directly attached to the shaft of the turbine (005). The remaining
energy of the exhaust gas drives the turbine and thus the compressor.

The number and the size of the turbochargers is accurately tuned to the engine and the number
of cylinders.

Fig 5-36

Turbocharger (example)

Legend

001

Compressor

005

Turbine

002

Air inlet

006

Exhaust gas outlet

003

Silencer

007

Exhaust gas inlet

004

Air outlet

If a turbocharger becomes defective, you must stop the engine as quickly as possible to prevent
damage.

If repair or replacement of a turbocharger is not immediately possible, you can cut out the defective
turbocharger, refer to

10.13 Temporary isolate a defective turbocharger

. Then the engine can

operate at decreased load, refer to the limits in

8.3 Start the engine - general

X52

AA00-6500-00AAA-043A-A

Operation Manual

Turbocharger

Winterthur Gas & Diesel Ltd.

- 178 -

Issue 002 2018-11

«
...
176
177
178
179
180
...
»

Summary of Contents for X52








































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X52

Brand: Ecco Pages: 3

Brand: Raytheon Pages: 69

Brand: Galaxy Audio Pages: 24

Brand: B&G Pages: 3

Brand: Gardner Bender Pages: 8

Brand: NARIKA Pages: 2

Saturn 2000 GC/MS

Brand: Varian Pages: 9

SeQual Eclipse 5

Brand: CAIRE Pages: 2

Alcotest 7410 GLC

Brand: Dräger Pages: 15

Brand: enz Pages: 40

Brand: KUHN Pages: 92

tynetec Aidcall

Brand: LEGRAND Pages: 6

Brand: SYSMEX Pages: 43

Brand: VWR Pages: 59

Brand: QUANTIFOIL Instruments Pages: 2

Brand: Nexus Pages: 79

Brand: Teletek electronics Pages: 2

Brand: PerkinElmer Pages: 285

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands