Winterthur Gas & Diesel Ltd. X52 Operation Manual Download

Page: 421 / 519

•

Trigger value

This list gives the value at which the related safeguard function starts.

For the analysis elements (AE) of concentration:

○

max - maximum concentration

For the level switches (LS) and flow switches (FS):

○

min - minimum or no flow

○

max - maximum flow

•

Delay

This list gives the delay of the action (in seconds) after the trigger value occurs.

X52

AA00-0000-00AAA-030K-A

Operation Manual

List of usual values and safeguard settings - general

Winterthur Gas & Diesel Ltd.

- 421 -

Issue 002 2018-11

Summary of Contents for X52








































































































































































































































































































































































































































































































































Search results

Summary of Contents for X52

Reviews:

Related manuals for X52

Brands by name

Popular brands

Winterthur Gas & Diesel Ltd. X52, Operation Manual

Search results

Summary of Contents for X52

Reviews:

Related manuals for X52

Brands by name

Popular brands