Winterthur Gas & Diesel Ltd. X52 Operation Manual Download

Page: 136 / 519

5.3

Group 3 - Crankshaft, connecting rod, and piston

5.3.1

Crankshaft

The crankshaft turns as it gets the power from the pistons. The crankshaft transmits the power to
the attached propeller shaft of the ship.

Main bearings on the two sides of each crank (002,

Figure 5-13

) hold the crankshaft in position.

The crankshaft gear wheel (005) is part of the thrust bearing.

On the driving end of the crankshaft there is a flywheel (004). This flywheel decreases the pulsation
from the cylinders.

The length of the crankshaft is related to the number of cylinders.

Fig 5-13

Crankshaft (generic)

001

002

003

004

005

Legend

001

Torsional vibration damper (optional)

004

Flywheel

002

Crank

005

Crankshaft gear wheel

003

Crankshaft

X52

AA00-3103-00AAA-043A-A

Operation Manual

Crankshaft

Winterthur Gas & Diesel Ltd.

- 136 -

Issue 002 2018-11

Summary of Contents for X52








































































































































































































































































































































































































































































































































Search results

Summary of Contents for X52

Reviews:

Related manuals for X52

Brands by name

Popular brands

Winterthur Gas & Diesel Ltd. X52, Operation Manual

Search results

Summary of Contents for X52

Reviews:

Related manuals for X52

Brands by name

Popular brands