1-34
UPDATE GAME CODE (You will typically want to run the latest update).
Use this menu to enable or disable the update game code (stored in the PRISM board FLASH
memory).
Enable Updated Code
If the update game code is enabled, the system will run the last version of update game code
installed (REFERENCE SOFTWARE UPDATES IN NEW FEATURES OF PINBALL 2000).
Disabled Updated Code
If the update game code is disabled, the system will run the version of game code located in the
original PRISM board ROMs.
WARNING TO THE OPERATOR.
In early releases of the Revenge from Mars game code ROMs, DO NOT perform the
Disabled Updated Code. Doing so will cause your game to run in Free Only Mode and the
UPDATE GAME CODE utility menu will not allow the updated game code to be enabled.
If you accidentally disable the update game code, do one of the following:
1) Plug a keyboard into the keyboard port (located near the computer case in the backbox) or,
2) Plug a computer terminal into the COM 1 port (located near the coin door).
Then, at the command (%) prompt type the following:
% fupdate enable
to re-enable the Updated Game Code.
Note: This operation takes about 15 seconds to complete.
SET CLOCK
Press the Enter button to activate the clock. Use the Up and Down buttons to change the time,
then press the Enter button to lock in the time.
INSTALL PRESETS
Press the Enter button to view the presets. Use the Up and Down buttons to move the cursor
and select from the available presets. When the desired Preset is selected, press the Enter
button to lock it in. Press the Escape button, during the 'countdown' to retain the original setting
and return to the Utilities Menu.
PRESET TABLE for Game Specific Adjustments
Preset Name
Extra
Easy
Easy
Medium
Hard
Extra
Hard
Multiball Rematch Time
30 sec
25 sec
20 sec
15 sec
10 sec
Hits to Light Locks
0
0
0
1
2
Targets Help Start Scene
5
4
3
2
0
Destroyer Droid Scene Speed
Slow
Slow
Medium
Medium
Fast
Hover Tank Scene Speed
Slow
Slow
Medium
Fast
Fast
Musical Chairs Silence
30 sec
25 sec
20 sec
15 sec
10 sec
Probe Droid Scene Speed
Slow
Slow
Medium
Fast
Fast
Side Targets Difficulty
Easy
Medium
Medium
Hard
Hard
Skill Shots for Awards
1
2
3
3
3
C3P0 Game Start Spot
6
5
4
2
0
C3P0 Memory
Yes
Yes
Yes
Yes
No
Lasers at Game Start
20
15
10
10
5
Maximum Laser Count
70
60
50
40
30
GUNGAN Memory
Yes
No
No
No
No
Summary of Contents for Pinball 2000 Star Wars Episode I
