Welch Allyn PneumoCheck 61000 Service Manual Download Page 59

Page: 59 / 90

58 Pneumocheck Handle and Printer/Charger

Service Manual 610132 Rev. E

The RED wire of the connector to the rotary
board (part of the TOP PANEL ASSEMBLY)
should be to the RIGHT.

Torque (items 18 and 19) to 3 - 4 in. lbs.
Torque (item 2) to 2.7 - 3 - 4 in. lbs.

Removing the CONTROL P. C. BOARD
ASSEMBLY (item 10)

Remove the TOP PANEL ASSEMBLY
(item 1) as instructed in Part A.

Remove the three screws (item 26) that
hold the CONTROL P .C. BOARD
ASSEMBLY.

Remove the CONTROL P.C. BOARD
ASSEMBLY.

Reassembly is the reverse of disassembly.

NOTE:

Torque (item 26) to 1.0 - 1.5 in. lbs.

Removing the SPRING CONTACTS (item 13)

Remove the TOP PANEL ASSEMBLY
(item 1) as instructed in Part A.

Remove the screws (items 12) securing
the SPRING CONTACTS to the MAIN
P.C. BOARD ASSEMBLY (item 14).

Remove the SPRING CONTACTS.

Reassembly is the reverse of disassembly.

Torque item 12 to 1.5 - 2.0 in.lbs.

Section 5 - Disassembly and Repair

Summary of Contents for PneumoCheck 61000



























































































Search results

Summary of Contents for PneumoCheck 61000

Reviews:

Related manuals for PneumoCheck 61000

Brands by name

Popular brands

Welch Allyn PneumoCheck 61000, Service Manual

Search results

Summary of Contents for PneumoCheck 61000

Reviews:

Related manuals for PneumoCheck 61000

Brands by name

Popular brands