Welch Allyn PneumoCheck 61000 Service Manual Download Page 5

Page: 5 / 90

4 Pneumocheck Handle and Printer/Charger

Service Manual 610132 Rev. E

Help Information:

•

All service and repairs must be performed by authorized Welch Allyn personnel or
agents, using Welch Allyn replacement parts. Failure to do so will invalidate the
product warranty.

•

If you have any questions about servicing the 61000 Pneumocheck or the 76100 or
76105 Printer Chargers, please call or write Welch Allyn:

Attn: Product Service Department

Welch Allyn, Inc.

4341 State Street Road

Skaneateles Falls, NY 13153-0220

U.S.A.

Telephone: 800-535-6663

Fax: 315-685-4653

•

Troubleshooting assistance is contained in Section 4 of this manual.

•

Please read and understand the PneumoCheck and Printer/Charger Operating
Instructions PN 610140-3.

Summary of Contents for PneumoCheck 61000



























































































Search results

Summary of Contents for PneumoCheck 61000

Reviews:

Related manuals for PneumoCheck 61000

Brands by name

Popular brands

Welch Allyn PneumoCheck 61000, Service Manual

Search results

Summary of Contents for PneumoCheck 61000

Reviews:

Related manuals for PneumoCheck 61000

Brands by name

Popular brands