Welch Allyn PneumoCheck 61000 Service Manual Download Page 54

Page: 54 / 90

Service Manual 610132 Rev. E

Pneumocheck Handle Printer/Charger 53

Remove the ELECTRONIC
COMPONENT ASSEMBLY.

NOTES:

Torque items 20 and 7 to 5 - 6.25 in. lbs.
Torque item 5 to 1.1 to 1.3 in. lbs.

Reassembly is the reverse of disassembly.

Removing the FRONT HOUSING ASSEMBLY
(item 21)

Remove the PNEUMOTACH
ASSEMBLY (item 18) as instructed in
Part B.

Remove the REAR BASE ASSEMBLY
(item 2) as instructed in Step C, Steps 1
- 5.

Remove the ELECTRONIC
COMPONENT ASSEMBLY (item 18) as
instructed in Part D.

Remove the FRONT HOUSING
ASSEMBLY.

NOTE:

If the FRONT HOUSING ASSEMBLY is

being replaced, copy the serial number from the old
assembly onto the blank label of the new assembly.

Reassembly is the reverse of disassembly.

Removing the BATTERY CONTACTS (P/N
610067)

Section 5 - Disassembly and Repair

Service Manual 610132 Rev. E

Summary of Contents for PneumoCheck 61000



























































































Search results

Summary of Contents for PneumoCheck 61000

Reviews:

Related manuals for PneumoCheck 61000

Brands by name

Popular brands

Welch Allyn PneumoCheck 61000, Service Manual

Search results

Summary of Contents for PneumoCheck 61000

Reviews:

Related manuals for PneumoCheck 61000

Brands by name

Popular brands