Welch Allyn PneumoCheck 61000 Service Manual Download Page 23

Page: 23 / 90

22 Pneumocheck Handle and Printer/Charger

Service Manual 610132 Rev. E

A set of specification drawings have been included in
Section 7 with reference made to them here. The
following tests should be done before the unit is
returned to the customer.

Calibrate and test the handle per specification
drawing A01945. “Calibrating with Welch Allyn
Spirometer.

Perform all tests on specification drawing
A01951, “Dynamic Waveform Testing”

For troubleshooting use, specification drawing
A01943 has been included for testing at the
PC Board Level.

Perform Dielectric Strength Test per:

A00167- UL/CSA Models
A00178- IEC Models

Perform Leakage Current Test per A00171

Perform Grounding Continuity Test per:

A00172 - UL/CSA
A02242 - IEC

Perform all tests listed on A01958, “Base Final
Testing”

For troubleshooting use, specification drawing
A01946 has been included for testing at the PC
Board Level.

2.4 TEST AND

ADJUSTMENTS

PNEUMOCHECK HANDLE

PNEUMOCHECK PRINTER/

CHARGER

Section 2 - Service

Summary of Contents for PneumoCheck 61000



























































































Search results

Summary of Contents for PneumoCheck 61000

Reviews:

Related manuals for PneumoCheck 61000

Brands by name

Popular brands

Welch Allyn PneumoCheck 61000, Service Manual

Search results

Summary of Contents for PneumoCheck 61000

Reviews:

Related manuals for PneumoCheck 61000

Brands by name

Popular brands