Welch Allyn PneumoCheck 61000 Service Manual Download Page 49 | Manualshive

Page: 49 / 90

background image

48 Pneumocheck Handle and Printer/Charger

Service Manual 610132 Rev. E

Trim.Lim

Handle cannot trim the baseline. May be due to an
abrupt thermal change or weak battery.
If not, may be hardware failure. If so, turn handle off/on.
If unit does not clear, return for service.

TX Fail (Transmission Fails)

Broken or bent contact in handle or printer? Push
paper feed button - Does paper feed through
machine.

If not: Is there paper in the machine?
Is paper tension lever (red, near paper roll) pushed
back all the way? Make sure that paper is properly
fed. There could be a paper jam.

To clear: Depress STOP & FEED buttons
simultaniously. Release STOP button. This will feed
paper backwards. Release FEED button. This should
clear the jam. Depress FEED button - paper should
flow through OK.
Printer does not advance paper and/or unit grinds
or strains when the feed button is depressed.
As a “last ditch” effort, unplug the printer ar the back
and plug it in again - this should reset the machine.

Unsteady

While in the “steady” mode, was the handle moved?

If not, problem could be a bad tranducer - handle
must be returned for repair.

Section 4 -Troubleshooting

«
...
47
48
49
50
51
...
»

Summary of Contents for PneumoCheck 61000



























































































Reviews:

No comments

Related manuals for PneumoCheck 61000

Brand: Kawai Pages: 66

miniSERIES Series

Brand: Valeport Pages: 25

Seeker 400 Series

Brand: General Pages: 24

Brand: shelyak Pages: 45

Brand: Agilent Technologies Pages: 198

Brand: Wacom Pages: 23

Brand: dacell Pages: 39

Brand: Eddy Wireless Pages: 18

Expert PDU energy 8001

Brand: Gude Pages: 22

Brand: ILITCH ELECTRONICS Pages: 2

PowerMaster MTA15Z

Brand: PowerMetrix Pages: 13

Digalox DPM72-MPPV

Brand: TDE Instruments Pages: 8

Brand: jenway Pages: 53

Brand: Hanna Instruments Pages: 52

Brand: Ress Pages: 11

Brand: Hanna Instruments Pages: 2

Brand: paratronic Pages: 4

Brand: Aquametro Oil & Marine Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands