Welch Allyn CP 150 Service Manual Download Page 88

Page: 88 / 133

Remove the LCD frame and display assembly

•

Separate the top housing assembly from the bottom housing assembly as described.

1. Remove the Pro-Gaff tape that holds the power switch flex cable to the LCD frame

and the top housing assembly.

2. Remove the six shoulder screws on the LCD frame using a #2 Phillips bit.
3. Remove the LCD frame.
4. Remove the LCD display and gasket from the top housing assembly.

Note

: Be sure to support the LCD display if you are removing it with the frame.

5. Remove the LCD display gasket.

Set aside the LCD gasket for reassembly.

6. Unlock the LCD flex connector from the LCD display assembly.

84 Disassembly, repair, and reassembly

CP 150 12-lead resting electrocardiograph

Summary of Contents for CP 150






































































































































Search results

Summary of Contents for CP 150

Reviews:

Related manuals for CP 150

Brands by name

Popular brands

Welch Allyn CP 150, Service Manual

Search results

Summary of Contents for CP 150

Reviews:

Related manuals for CP 150

Brands by name

Popular brands