Welch Allyn CP 150 Service Manual Download Page 56

Page: 56 / 133

USB host test

Note

Welch Allyn has not validated specific USB flash drives. Use only 64Gb or
less USB flash drives.

1. Insert a USB flash drive into each of the four ports on the back of the device and

follow the instructions on the screen to test each of the ports.

2. Touch

USB host test

to test each port from left to right.

3. Touch (Next) to perform the next functional test.

USB client test

1. Connect a USB type mini-B connector to the device client USB port and a type A

connector to a free USB port on the PC. Verify that the PC is able to recognize

CP150 device.

2. Touch

Yes

to confirm that your PC recognized the CP 150 device, or touch

if your

PC did not recognized the CP 150 device.

3. Touch (Next) to perform the next functional test.

52 Service

CP 150 12-lead resting electrocardiograph

Summary of Contents for CP 150






































































































































Search results

Summary of Contents for CP 150

Reviews:

Related manuals for CP 150

Brands by name

Popular brands

Welch Allyn CP 150, Service Manual

Search results

Summary of Contents for CP 150

Reviews:

Related manuals for CP 150

Brands by name

Popular brands