Welbilt Convotherm OES mini easyTouch Installation Manual Download Page 94

Page: 94 / 106

Dissipated heat

The following table shows the heat output figures:

Dissipated heat

6.06 mini

6.10 mini

10.10 mini 6.10 min

2in1

Latent heat

[kJ/h]

1000

1330

1850

3700

[kW]

0.28

0.37

0.51

1.03

Sensible heat

[kJ/h]

1100

1450

2030

2370

[kW]

0.31

0.40

0.56

0.69

Water connection

The following table shows the values for the water supply:

Water connection
Water supply (cold only)
Shut-off device

With EA (verifiable) check valve and dirt

filter

For Australia / New Zealand:

With double check valve (DCV) and dirt

filter

Water supply
Connection

2 x G 3/4'', Fixed connection recom‐

mended

Flow pressure (without ConvoClean system

option)

[kPa]

200 - 600 kPa (2 - 6 bar)

Flow pressure (with ConvoClean system op‐

tion)

[kPa]

300 - 600 kPa (3 - 6 bar)

Water drain
Model

Fixed connection (recommended) or

funnel waste trap

Type

For 6.06/6.10/10.10 mini: DN 40

For 6.06 mini 2in1: DN 50

Water quality

The following table shows the values for the water quality:

Water quality
Water quality for general use

Drinking water, typically soft water

(install water treatment system if neces‐

sary)

Hardness for injection
German degrees of hardness (general hard‐

ness: GH)

[°dH]

4 - 7

French degrees of hardness

[TH]

7 - 13

English degrees of hardness

[°e]

5 - 9

International

[ppm]

70 - 125

Chemical

[mmol/l]

0.7 - 1.3

Hardness for condenser, cleaning
German degrees of hardness (general hard‐

ness: GH)

[°dH]

4 - 20

French degrees of hardness

[TH]

7 - 35

English degrees of hardness

[°e]

5 - 25

9 Technical data and Connection drawing

Installation manual

Summary of Contents for Convotherm OES mini easyTouch











































































































Search results

Summary of Contents for Convotherm OES mini easyTouch

Reviews:

Related manuals for Convotherm OES mini easyTouch

Brands by name

Popular brands

Welbilt Convotherm OES mini easyTouch, Installation Manual

Search results

Summary of Contents for Convotherm OES mini easyTouch

Reviews:

Related manuals for Convotherm OES mini easyTouch

Brands by name

Popular brands