Welbilt Convotherm OES mini easyTouch Installation Manual Download Page 67

Page: 67 / 106

6.2 Water connection

Purpose of this section

This section shows you how to install the water connection.

6.2.1

Safe working when making the water connection

For your safety

Before starting work, familiarize yourself with the hazards described in Hazards and safety precautions

during installation on page 25.

Eligibility of personnel for the water connection

Only qualified personnel from an approved customer service office are permitted to connect the combi

oven to the water supply.

Personal protective equipment

Wear the personal protective equipment specified in the section 'Personal protective equipment' on

page 39 of the 'For your safety' chapter for the relevant tasks.

Regulations for the water connection

Water pipes and connections must comply with local and national regulations. In particular these in‐

clude:

■

DIN 1988 part 2 and part 4

■

EN 61770

■

EN 1717

For appliances with an NSK certificate, the following regulations must also be observed:

■

Regulations from the National Sanitation Foundation (NSF)

■

International Plumbing Code 2003

■

International Code Council (ICC)

■

Uniform Plumbing Code 2003, International Association of Plumbing and Mechanical Officials (IAP‐

MO)

The appliance must be installed with suitable backflow protection to comply with applicable federal,

state, and local codes.
For Australia and New Zealand:

The water pipes must be installed in compliance with AS/NZS 3500 Plumbing and Drainage Code.
Australia only:

The double check valve supplied with this appliance must be installed in the water supply line to this

appliance to provide the backflow prevention required by the Plumbing Code of Australia.

6 Installation

Installation manual

Summary of Contents for Convotherm OES mini easyTouch











































































































Search results

Summary of Contents for Convotherm OES mini easyTouch

Reviews:

Related manuals for Convotherm OES mini easyTouch

Brands by name

Popular brands

Welbilt Convotherm OES mini easyTouch, Installation Manual

Search results

Summary of Contents for Convotherm OES mini easyTouch

Reviews:

Related manuals for Convotherm OES mini easyTouch

Brands by name

Popular brands