Welbilt Convotherm OES mini easyTouch Installation Manual Download Page 18

Page: 18 / 106

3.3

Warning signs on the combi oven (6.06/6.10/10.10 mini)

Where are the warning signs fitted?

The following figure shows the 6.06 mini combi oven (representative of all appliance sizes).
The warning signs are located in the following positions:

Warnings on the appliance door

The following warning signs (2) are fitted on the appliance door above the door handle:

Warning sign

Description
Warning of hot food, hot food containers and hot liquids

There is a risk of burns from hot food and hot food containers if food containers

tip out of the shelf levels or food slips off food containers that are not held level.

This risk is particularly high for shelf levels that lie above the sightline of the

user.

Spillage of hot liquid foods can result in scalds if the upper shelf levels are loa‐

ded with liquids or foods that produce liquid during cooking. Do not use shelf

levels that lie above your sightline for liquid foodstuffs or food that will liquefy

during cooking.
Hot steam and vapour hazard warning

There is a risk of scalding from hot steam and vapour escaping when the appli‐

ance door is opened.

Only for ConvoClean system option

Warning of corrosive cleaning agents injected into oven

There is a risk of chemical burns or irritation to skin, eyes and respiratory sys‐

tem from contact with sprayed cleaning agents and their vapours if the appli‐

ance door is opened during fully automatic cleaning by the ConvoClean system.
Only for a mobile supporting structure

Tipping or toppling warning for combi oven

There is a risk of the combi oven toppling over if moved. Always take great care

when moving the combi oven.
Only for a mobile supporting structure

Damage or detachment warning for appliance connections

There is a risk of the appliance connections being damaged or detached if the

combi oven is moved. Always ensure there is enough length in the supply ca‐

bles and pipes when moving the combi oven. After moving, always secure the

combi oven against rolling away.

3 For your safety

Installation manual

Summary of Contents for Convotherm OES mini easyTouch











































































































Search results

Summary of Contents for Convotherm OES mini easyTouch

Reviews:

Related manuals for Convotherm OES mini easyTouch

Brands by name

Popular brands

Welbilt Convotherm OES mini easyTouch, Installation Manual

Search results

Summary of Contents for Convotherm OES mini easyTouch

Reviews:

Related manuals for Convotherm OES mini easyTouch

Brands by name

Popular brands