Welbilt Convotherm OES mini easyTouch Installation Manual Download Page 64

Page: 64 / 106

6.1.3 Carrying out the electrical installation

Requirements

Check that the following requirement has been met:

■

The connection point of the appliance is disconnected from the customer power supply and protec‐

tive measures taken to ensure the power cannot be switched on again.

Checking the supply ratings and electrical connections

Follow the steps below to check the connection to the installation system and the electrical connec‐

tions:

Step

Action

Illustration

Remove the rear panel from the appliance.

The circuit diagram and spare parts list are located in

the wiring compartment.

Check that the electrical supply ratings on the type plate

match the figures for the installation system and those

given in the circuit diagram. It is only permitted to con‐

nect the combi oven if all these values tally with each

other.

Check all screw connections and terminals on the appli‐

ance. The connections may have worked loose during

transport.

Carrying out the electrical installation

Follow the steps below to connect your appliance to the electrical supply:

Step

Action

Illustration

Connect the appliance at the designated connection

point (1) to an equipotential bonding system.

Use the mains power cord to connect the power supply

to the appliance at the -X10 terminal strip (2).

Make sure that the cable gland (3) is tightened firmly

because it also acts as a cable strain relief.

Reset the thermal cutout if necessary.

Fit the rear panel on the appliance and check that it is

fixed correctly in place.

6 Installation

Installation manual

Summary of Contents for Convotherm OES mini easyTouch











































































































Search results

Summary of Contents for Convotherm OES mini easyTouch

Reviews:

Related manuals for Convotherm OES mini easyTouch

Brands by name

Popular brands

Welbilt Convotherm OES mini easyTouch, Installation Manual

Search results

Summary of Contents for Convotherm OES mini easyTouch

Reviews:

Related manuals for Convotherm OES mini easyTouch

Brands by name

Popular brands