Welbilt Convotherm OES mini easyTouch Installation Manual Download Page 26

Page: 26 / 106

Safety hazard: mechanical parts of the appliance

When installing the appliance, be aware of the following hazards and take the specified preventive ac‐

tions:

Danger

Where or in what situations

does the hazard arise?

Preventive action

Safety device

Risk of cuts from sharp

edges

When handling sheet-metal

parts

■

Exercise caution when

performing these tasks

■

Wear personal protective

equipment as specified in

safety regulations

None

Safety hazard: cleaning agent

When installing the appliance, be aware of the following hazards and take the specified preventive ac‐

tions:

Danger

Where or in what situations

does the hazard arise?

Preventive action

Safety device

Risk of chemical burns

or irritation to skin, eyes

and respiratory system

from contact with clean‐

ing agents and their va‐

pours.

When corrosive cleaning

agents are used

Only use those cleaning

agents specified under

Cleaning agents in the

'Cleaning and Servicing'

chapter of the user manual.

None

For 6.06/6.10/10.10 mini with

ConvoClean system option:

When fitting the cleaning sys‐

tem

■

Wear personal protective

equipment

■

Observe the labels on the

cleaning agents and the

relevant safety data‐

sheets

None

For 6.10 mini 2in1:

When handling the cleaning

agent drawer and rinse aid

drawer

■

Wear personal protective

equipment

■

Close the cleaning agent

drawer and rinse aid

drawer carefully without

jolting to avoid any clean‐

ing agent slopping out.

None

3 For your safety

Installation manual

Summary of Contents for Convotherm OES mini easyTouch











































































































Search results

Summary of Contents for Convotherm OES mini easyTouch

Reviews:

Related manuals for Convotherm OES mini easyTouch

Brands by name

Popular brands

Welbilt Convotherm OES mini easyTouch, Installation Manual

Search results

Summary of Contents for Convotherm OES mini easyTouch

Reviews:

Related manuals for Convotherm OES mini easyTouch

Brands by name

Popular brands