Welbilt Convotherm OES mini easyTouch Installation Manual Download Page 69

Page: 69 / 106

6.2.2 Water supply

Rules for safe installation of the water supply

Observe the following rules to prevent hazards caused by a faulty water connection:

■

For appliances with a wheeled platform, the water supply must be provided via a flexible water sup‐

ply line.

■

The length of the water connection must accommodate the range of movement allowed to the ap‐

pliance by the retaining device on the wheeled platform. When moving the assembly (platform plus

appliance), never strain or wheel over the water supply pipe.

Connecting the water supply

The combi oven is designed to be fixed connected to the customer's water supply. Dirt filters must be

provided.

Connecting the water supply with a flexible connecting pipe

The combi oven can be connected to the water supply using a flexible DN10 connecting pipe to DIN

EN 61770 with a 3/4" screw connection. Dirt filters must be provided.

Water quality and water hardness

Check the water quality as specified in Testing the water quality on page 75.
Compare the water quality and water hardness of the in-house supply with the values specified in the

'Technical Data' chapter (see Water quality on page 94). If the specified conditions are not satisfied,

you must install suitable water filters and water treatment equipment. Please refer to the Technical Da‐

ta and Connection Drawing on page 92 section for details of the required capacities.

Installation diagram without water treatment (6.06/6.10/10.10 mini)

The following diagram shows the connection diagram for water installations without water treatment:

4 - 20 °d H
7 - 27 °T H
5 - 19 °e
70 - 270 ppm
0, 7 - 2, 7 m mo l/l

2 - 6 bar

max. 40 °C
min. 20 µS/cm

6,5 - 8,5

max. 100 mg/l

SO4

max. 150 mg/l

max. 0,1 mg/l

6019164

4 - 7 ° dH
7 - 13 °T H
5 - 9 ° e
70 - 125 ppm
0, 7 - 1, 3 m mo l/l

2 - 6 bar

max. 40 °C
min. 20 µS/cm

6,5 - 8,5

max. 100 mg/l

SO4

max. 150 mg/l

max. 0,1 mg/l

6019165

Item Name

Explanation

Soft water connection

Drinking water quality, see Technical data on page 92

Cold water connection

Water distributor

Water supply line

0.08 mm sediment filter

A 0.08 mm sediment filter must be installed if the water has

a high level of impurity.

Shut-off device with dirt filter

Verifiable check valve

Type EA

6 Installation

Installation manual

Summary of Contents for Convotherm OES mini easyTouch











































































































Search results

Summary of Contents for Convotherm OES mini easyTouch

Reviews:

Related manuals for Convotherm OES mini easyTouch

Brands by name

Popular brands

Welbilt Convotherm OES mini easyTouch, Installation Manual

Search results

Summary of Contents for Convotherm OES mini easyTouch

Reviews:

Related manuals for Convotherm OES mini easyTouch

Brands by name

Popular brands