Welbilt Convotherm mini black easyTouch 10.10 Installation Manual Download Page 115

Page: 115 / 148

5.2 Adjacent Systems

Handling exhaust air

During operation, the combi oven will produce heat and moisture, most of which will escape upwards

into the ambient air in the form of hot steam coming through the air vent. Do not connect any lines or

ducts directly to the combi oven's air vent!

The manufacturer recommends removing this exhaust air from the combi oven's working area with a

range hood or ventilated ceiling.

In order to prevent fire hazards and other structural issues, such as corrosion, mold, and/or a de‐

crease in stability, there must be sufficient clearance between the top of the unit and the ceiling. This

clearance must be determined by taking the following into account:

■

The reference point for the minimum vertical clearance (refer to 'Installation Location Require‐

ments' on page 41).

■

The type of exhaust system being used

■

The characteristics of the ceiling at the installation location

The combi oven must always be set up, installed, and operated in compliance with all applicable coun‐

try-specific and local standards and regulations.

5 Setup

Installation Manual

Summary of Contents for Convotherm mini black easyTouch 10.10





















































































































































Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands

Welbilt Convotherm mini black easyTouch 10.10, Installation Manual

Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands