Welbilt Convotherm mini black easyTouch 10.10 Installation Manual Download Page 78

Page: 78 / 148

FOR THE INSTALLER, OPERATOR, RESPONSIBLE OWNER

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors or liquids in the

vicinity of this or any other unit.

WARNING

Improper installation, adjustment, alteration, service or maintenance can

cause property damage, injury and death. Read the installation, operating

and maintenance instructions thoroughly before installing or servicing this

equipment.

WARNING

To reduce the risk of electric shock, do not remove or open cover.
No user serviceable parts inside. Refer servicing to qualified personnel.

Disconnect power supply before servicing.

WARNING

Disconnect power at the main external power switch before servicing or

repairing a combi oven.

IMPORTANT

ALL SERVICE MUST BE PERFORMED BY A QUALIFIED CONVOTHERM AUTHORIZED TECHNI‐

CIAN.

KEEP AREA FREE AND CLEAR OF COMBUSTIBLES.

Installation

■

Installation of this unit must be done by a licensed professional when installed in the Commonwealth

of Massachusetts.

■

The wiring diagram is located on the inner part of the side panel.

Customer documentation

■

The customer documentation is part of the combi oven.

■

Keep the customer documentation manuals handy at all times so that you can look up any required

information.

■

Keep the customer documentation manuals for the entire life of the unit.

■

Carefully read the installation manual, the operating manual, and the operating instructions before

using, handling, and working on this unit.

■

If you transfer the combi oven to a new owner, make sure to give the new owner the customer doc‐

umentation manuals as well.

Summary of Contents for Convotherm mini black easyTouch 10.10





















































































































































Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands

Welbilt Convotherm mini black easyTouch 10.10, Installation Manual

Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands