Welbilt Convotherm mini black easyTouch 10.10 Installation Manual Download Page 39

Page: 39 / 148

4.2 Transporting the unit to the installation location

Required space during transportation

Make sure that the transportation route you will be following has enough space to accommodate the

unit's entire width and height at all times.
The following table provides the minimum door width and height required in order to be able to get the

combi oven to its intended installation location.

Minimum door opening di‐

mensions

Width

[in]

22.8

Height

[in]

32.7

Load capacity for transportation

Make sure that the transportation equipment you will be using is able to handle the loads it will be

transporting.
The required minimum load capacity for the transportation equipment is 150 lbs.

Transporting the unit to the installation location

Observe the following when transporting the unit:

■

Always use a pallet to transport the unit.

■

Always keep the unit upright when moving it.

■

Transport the unit slowly and carefully and secure it in such a way that it cannot tip over.

Make sure not to bump into the unit.

Avoid uneven transportation routes and steep inclinations.

4 Transportation

Installation Manual

Summary of Contents for Convotherm mini black easyTouch 10.10





















































































































































Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands

Welbilt Convotherm mini black easyTouch 10.10, Installation Manual

Search results

Summary of Contents for Convotherm mini black easyTouch 10.10

Reviews:

Related manuals for Convotherm mini black easyTouch 10.10

Brands by name

Popular brands